Level 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Before
After
Before
After
Before
AfterOlympia Chimney Chimney Liner & Rebuild in Framingham: What to Know First
We rebuild and reline Olympia Chimney systems in Framingham as an independent Olympia Chimney service provider, which means we are not tied to a manufacturer’s script and we are not a warranty call center. A typical liner replacement or partial rebuild runs one to two days once we have the parts in hand, and we give you the full price before any work starts. If you own an Olympia Chimney fireplace, stove, or insert and the liner is showing its age, call (781) 390-9211 and Wendell will walk you through what you are actually looking at.
This page is for Framingham homeowners who have an Olympia Chimney product and want straight answers about liners and rebuilds. Not brand marketing. What actually fails, what it costs here, and how we fix it.
How Olympia Chimney Products Fail - and How We Fix Them
- Olympia Chimney zero-clearance fireplace liners with seam separation. We see this on older Olympia ZC units around Framingham, especially in homes built in the 1980s and 1990s up near Nobscot and Saxonville. The factory liner sections were joined with seams that, after twenty-plus New England freeze-thaw cycles, start to pull apart. You will not see it from the firebox. We catch it with a camera run. Fix is a new stainless liner sized to the existing chase, and we do not patch seams on these, we replace the liner run.
- Flexible liners kinked during original installation. Olympia Chimney flexible liners are fine products, but if the original installer forced one around a tight offset in the flue, that kink becomes a creosote shelf. In Framingham, where wood stoves run hard from October to April, a kinked liner loads up with second-degree creosote within a season. We pull the old liner, correct the offset with proper fittings, and pull a new liner through without the kink. The difference on a camera screen is obvious.
- Mix-and-match parts from a previous repair. Olympia Chimney components are engineered to work as a system. When a handyman or a lowest-bid crew swapped in a generic anchor plate or a non-Olympia cap because it was what the supply house had that day, we see draft problems and water entry at the joints. As an independent Olympia Chimney service provider, we match components properly, using OEM Olympia parts where they matter structurally and honest aftermarket equivalents where they do not.
- Clay tile liner failure behind the Olympia appliance connector. The Olympia unit may be fine. The masonry chimney behind it often is not. Framingham’s freeze-thaw cycles crack old clay tiles, and once a tile spalls, the gap lets flue gas into the chase. We rebuild the masonry section, drop in a properly sized stainless liner, and reconnect the Olympia appliance to it with the right adapter. The fireplace itself never has to leave.
- Water damage at the top plate and chase cover. Olympia Chimney chases use metal top plates that eventually rust once the cap seal fails. Water runs down the outside of the liner, rusts the liner wall, and you get flaking metal inside the flue. We replace the chase cover, inspect the liner, and if the liner wall is compromised, we reline. This is one we can usually spot from the ground with binoculars before we even set a ladder.
Our Olympia Chimney Chimney Liner & Rebuild Process
- 1
Call and talk to a person. You call (781) 390-9211. Wendell or one of his crew answers. You describe what you are seeing, and we schedule a time. No call center, no third-party booking.
- 2
On-site inspection with camera. We run a camera through the entire flue, from the appliance connector to the cap. You see the footage. We explain what it means in plain English. If it does not need a liner, Wendell will tell you that too. His words: “If it doesn’t need doing, I’ll tell you.”
- 3
Parts decision. If it is an Olympia Chimney component that needs replacing, we use OEM where the part carries the system’s integrity: anchor plates, appliance adapters, and caps. For liners themselves, we will offer you a choice of Olympia OEM or a quality alternative from DuraFlex or HeatShield depending on your budget and the appliance. You get the price difference in writing before we order.
- 4
The rebuild or reline. We mobilize, protect the work area, pull the old liner or rebuild the damaged masonry section, and install the new liner with proper support and insulation where the install calls for it. This is one to two days for most Framingham jobs.
- 5
Test and document. We run the camera again after the work and test draft before we call it done. You get before-and-after footage.
- 6
Paperwork and the 90-Day Done Right Promise. Your invoice shows exactly what was done, what parts were used, and the price we quoted before we started. Every job carries our 90-Day Done Right Promise in writing. One call brings us back at no additional cost if something is not right.
What Olympia Chimney Chimney Liner & Rebuild Costs in Framingham
Straight numbers, because that is what you need to plan around. A flexible stainless liner replacement for a wood stove on an existing Olympia Chimney setup in Framingham typically runs $1,400 to $2,600, depending on flue height and access. A full liner plus chase cover and cap replacement is generally $2,200 to $3,800. A partial masonry rebuild with a new liner typically lands between $3,500 and $6,500. A full chimney rebuild from the roofline up can run $7,000 to $14,000, depending on scaffolding and brick matching.
What moves the price: roof pitch, flue height, whether the old liner comes out clean or fights us, and whether we are matching old brick or working with a stucco or stone chase. You will know your number before we start, and it will not change unless we find something genuinely dangerous, which we will show you on camera before we spend a dollar. Call (781) 390-9211 for a free estimate.
Why Framingham Homeowners Call Top Hat Chimney for Olympia Chimney Work
We have been working chimneys in Framingham since 1999, which means we have been inside more Olympia Chimney systems than most installers will ever touch. Wendell Pike puts his name on every job, and his license number is published for anyone who wants to look. We also service the other brands you are likely to have in the house: DuraFlex, HeatShield, and Gelco. That matters when a previous homeowner mixed brands or when a quality aftermarket part is the honest call.
Every job carries the 90-Day Done Right Promise. Phones are answered by a live person around the clock. No trip charge inside the county. Seniors and veterans always get 10% off. And Wendell will tell you plainly when a liner can wait another season, which is why people around here keep his number.
FAQs
Warranty coverage depends on the original purchase terms and what component failed, not on who holds the brush. As an independent Olympia Chimney service provider, we are not a manufacturer-authorized dealer, which means warranty claims go through Olympia Chimney, not us. We will help you document the failure with camera footage and a written description so your claim has a real chance. If warranty will not cover it, we give you options from OEM to quality aftermarket. Call (781) 390-9211 and we will walk through what applies to your specific unit.
We keep common Olympia Chimney anchors, connectors, and caps on the truck during the early spring and into winter, which is when Framingham chimneys reveal themselves. Larger components and liners we order per job after the camera inspection, which is why we schedule at least a few days between diagnosis and the heavy work. The good news: since we are independent, we have access to multiple supply houses and do not wait on a single manufacturer’s fulfillment schedule. Call (781) 390-9211 and we will give you a straight timeline for your specific part.
Sometimes, but rarely on a liner that has been in service more than ten years. If the camera shows a small puncture or a failed seam in an otherwise sound liner, a stainless patch sleeved into place can buy you two to three seasons. But if the liner wall is thinning, rusting from the outside, or loaded with third-degree creosote glaze, a patch is just delaying the inevitable and you will pay twice. We will show you the footage and let you decide. Call (781) 390-9211 if you want a straight verdict before you spend anything.
Once we have the right liner and parts in hand, most single-flue relines are done in one working day. A partial rebuild adds a second day for masonry work and mortar cure. Between diagnosis and completion, expect four to ten days depending on part availability. If you are heading into burning season and your liner is compromised, call early. The fall calendar in Framingham fills up fast. Call (781) 390-9211 and we will give you a real date, not a window that stretches for weeks.
Written by Wendell Pike, Owner, Top Hat Chimney at Top Hat Chimney, serving Framingham and nearby areas.