Olympia Chimney Chimney Cap & Crown Nationwide

Olympia Chimney Chimney Cap & Crown in Framingham: What to Know First

We repair, replace, and install Olympia Chimney chimney caps and crowns across Framingham as an independent Olympia Chimney service provider. Most cap and crown jobs take one visit, with the work typically done same-day once we’ve seen the flue and confirmed measurements. Pricing runs honest and upfront: a standard Olympia Chimney cap replacement in Framingham usually lands between $225 and $475 installed, and a crown repair or recoat typically runs $350 to $800 depending on condition. If your Olympia Chimney cap is rusted through or your crown is spalling, call (781) 390-9211 and Wendell or one of the crew will talk you through what you’re seeing before anyone climbs a ladder.

Call (781) 390-9211

This page is for Framingham homeowners with an Olympia Chimney flue system who need a cap or crown addressed and want to know what’s actually wrong before spending money. No scare tactics, no mystery pricing. If it doesn’t need doing, we’ll tell you.

How Olympia Chimney Products Fail - and How We Fix Them

• Rusted multi-flue caps on older Olympia Chimney galvanized models. We see this a lot on homes around Nobscot and Saxonville where the original cap was installed with the furnace flue in the 1990s or early 2000s. The galvanized mesh and base plate corrode at the corners first, especially on the leeward side where Framingham’s wet winters sit against the metal. We replace with stainless steel Olympia Chimney caps or a quality aftermarket equivalent when the original is discontinued. The fix stops rain entry and keeps squirrels and starlings out of the flue.
• Cracked crowns on masonry chimneys with Olympia Chimney liners. The crown is a different animal than the cap, and it fails on its own schedule. Framingham freeze-thaw cycles push water into hairline cracks, the water freezes, and the crack widens. By spring you’ve got a spalling crown and water working down into the brick. We see this pattern every March. We grind out the damaged material, re-form the crown with a proper slope away from the flue tile, and seal it with a flexible crown coat that moves with the chimney.
• Improperly sized cap that chokes draft on Olympia Chimney air-cooled systems. Some Olympia Chimney caps installed by other contractors or by a previous homeowner sit too low over the flue opening or use mesh that’s too fine. The symptom is a fireplace that smokes back or a furnace that trips a pressure switch. The fix is not always a new liner, and it’s not always a new cap. We measure the actual opening and the cap’s clearance before we touch anything. Sometimes the cap just needs to be raised. We’ll show you the math.
• Loose or torn cap screens on Olympia Chimney top-mount caps. High winds off the Sudbury River valley work the screen brackets loose over time. Once the screen sags, it’s not keeping anything out, and it becomes a creosote trap on wood-burning flues. We re-secure the screen or replace the cap outright when the frame is too far gone. A sagging screen is one of those small things that turns into a blocked flue if it’s ignored through a winter.
• Water staining around the flue tile from a failed crown-to-liner joint. On homes with an Olympia Chimney stainless liner running through an older masonry chimney, the crown was often poured around the liner without a proper expansion joint. The metal expands, the crown doesn’t, and the joint cracks. Water follows the liner down and shows up as staining on the ceiling or a rusted damper. We re-cut the joint, install a flexible sealant collar that moves with the liner, and usually recommend a new cap with a proper storm collar. This is one of the most common things we fix on Framingham chimneys that were originally set up for a wood stove.

Our Olympia Chimney Chimney Cap & Crown Process

Here’s how a typical job goes from the first call to the last sweep of the brush.

1. 1
   You call and describe what you’re seeing. Wendell or a live person answers. You describe the rust, the crack, the water stain, the draft problem. We tell you honestly whether it sounds like a cap job, a crown job, or something else entirely.
2. 2
   We come out and look at the whole chimney, not just the cap. Ladder up, eyes on the crown, the cap, the flue tile, the brick. We check what’s actually failing and measure the flue opening. No charge to come out inside the county.
3. 3
   We give you the price before any tool comes off the truck. The number we quote on the driveway is the number on the invoice. If the job changes, we tell you before we touch it, and you decide.
4. 4
   Parts decision: OEM Olympia Chimney or quality aftermarket. If your model line is still supported, we use the OEM part. If it’s discontinued or backordered for months, we use a quality aftermarket cap that matches or exceeds the original spec. We’ll tell you which one you’re getting and why.
5. 5
   The repair or replacement. Cap goes on with proper clearance and sealed fasteners. Crown gets ground, re-formed, and coated. Multi-flue caps get secured to the crown with mechanical fasteners, not just adhesive.
6. 6
   We test the draft and walk you through it. We check the draw before we leave, show you the finished work, and leave you with the 90-Day Done Right Promise in writing. If something’s not right in that window, one call brings us back.

What Olympia Chimney Chimney Cap & Crown Costs in Framingham

Here are the ranges we quote most often in Framingham for Olympia Chimney cap and crown work:

• Standard single-flue cap replacement: $225 - $375 installed, depending on flue size and whether we’re matching an existing Olympia Chimney model or using a quality aftermarket equivalent.
• Multi-flue cap for a larger chimney: $350 - $475 installed. This covers custom-cut metal to span the flue area plus mechanical fastening to the crown.
• Crown repair with crack fill and recoating: $350 - $550. This is for crowns with scattered cracking but structurally sound concrete.
• Crown rebuild with new concrete and proper slope: $550 - $800. When the crown has spalled badly or the concrete is crumbling, we form and pour a new one.
• Custom cap or hard-to-match configuration: $500 and up. Odd flue spacing, very tall flue tiles, or a homeowner who wants a specific look will push the price up.

What moves the price: flue size, how much crown repair is needed, chimney height and roof pitch, and whether OEM parts are available. We don’t charge extra to come out inside the county, and we knock $40 off any repair over $200. Call (781) 390-9211 for an exact quote. The estimate is free whether you book the work or not.

Why Framingham Homeowners Call Top Hat Chimney for Olympia Chimney Work

Wendell Pike started Top Hat Chimney in 1999, and he’s the owner whose name is on the truck and on the invoice. When you call about an Olympia Chimney cap or crown in Framingham, you’re not getting a rotating crew from a national franchise. You’re getting a local owner-operator who has been on Framingham roofs for over two decades and knows which neighborhoods, from Nobscot to the south side, tend to have which chimney problems.

Every job we complete is backed by our 90-Day Done Right Promise in writing. If the cap leaks or the crown cracks inside 90 days, one call brings Wendell back at no charge. We also work with DuraFlex, HeatShield, and Gelco products, so if the cap and crown job turns up a liner issue underneath, we can handle the whole repair with one visit instead of sending you to someone else. Phones are answered by a real person around the clock, and every technician is background-checked and shows up in uniform with a real arrival window.

FAQs